Press Specifications:

·         100 U.S. Tons Capacity (890 kN)

·         1.00 in. Stroke (25 mm)

·         2.00 in. Slide Adjustment (51 mm)

·         20.12 in. Shutheight, SDAU, on Bed (511 mm)

·         48.00 x 20.50 in. Slide (1219 mm x521 mm)

·         48.00 x 32.00 in. Bed Area (1219 mm x 813 mm)

·         38.00 in. Distance, Floor to Top of Bed (965 mm)

·         50.00 in. Between Gibs (1270 mm)

·         15.00 in. Upright Opening (381 mm)

·         0 – 900 SPM (full energy above 300 spm)

·         40 HP, 1800 RPM Drive Motor (28.83 kW)

·         480 VAC, 60 hz, 3 ph incoming power

·         156.00 in. Overall Height (3962 mm)

·         134.00 in. Motor/guard removed (3404 mm)

·         31,400 lbs. Approximate Press Weight (14,243 kg)

Equipped With:

·         Flywheel Type

·         Left hand drive with extension on opposite end

·         Minster Hydraulic Clutch and Brake

·         Air Operated flywheel brake electrically interlocked

·         Frame of cast four piece tie rod construction

·         Minster “Monitorflow” recirculating oil lubrication system

·         Long barrel type manual slide adjustment arranged for detachableair operated wrench

·         Eight adjustable bronze lined gibs, F and B Includes

hydrostatic gibs

·         Auxiliary locking arrangement on each connection screw Minster integral dynamic balancing unit located on top of press which will permit operating up to full speed without being bolted down. Balancing unit is based on upper die weight of 500 lbs.

·         Sump Oil Heater - Controlled by PMC

Note:  All specifications contained herein are as the machine was originally manufactured and are subject to change at time of inspection.

ELECTRICAL CONTROL

MINSTER CENTRALIZED MOTOR AND CLUTCH CONTROL

PANEL, NEMA Type 12 enclosure, built to MINSTER’S

interpretation of ANSI – B11.1, and to NFPA Specifications.

Main panel contains the Minster Production Management Control with a fused disconnect, reversing drive starter.

Main panel also includes Minster Eddy Current drive motor

controller, speed control, and speed indicator. Includes torque limit controller.

Main control panel located in pedestal located off right hand front of press.Pedestal has standpipe and 6 ft. of flexible overhead conduit to swivel box on front of crown. (Customer’s power drop to be to pedestal.) Distance from bottom of press foot to centerline of overhead conduit to be approximately 129".

Set-up units located on operator’s pedestal include:

§  Power Off-On Locking Selector Switch

§  Supervisory Control Lock Selector Switch

§  Clutch Selector Switch to select Inching, Set-Up Cycle, or Continuous Operation.

§  Continuous Arm Illuminated Button

§  Set-Up Cycle Arm Illuminated Pushbutton

§  Master Stop Button

§  Top Stop Button

§  Stop Button

NOTE:

The SETUP CYCLE mode is a means of single cycling the press

slide for die setup and stock threading purposes. It is not intended for production purposes. Includes preset

MINSTER PRODUCTION MANAGEMENT CONTROL includes the

following features:

§  Color Touch Screen

§  Allen Bradley SLC 504/C PLC

§  16-Pole Programmable Limit Switch

§  Brake Monitor / Press Stopping Time Readout

§  75 Tool Storage Capacity with 7-Digit Alpha Numeric I.D. Codes

§  System Prompts and Diagnostic Messages

§  Press Lubrication System Indicators

§  Motor Start/Stop Control

§  Motor Forward/Reverse Control

§  Motor Speed Control

§  Motor Speed and Load Display

§  Dual Clutch Valve Monitor

§  Stock Lubricator Interface Output

§  Auxiliary output interface for secondary control elements

o    2nd blowoff

o    Lubricator

o    diverter tables, etc.

§  Blowoff Valve Interface Output

§  Production Counters

o    Totalizers

o    Preset/Batch

§  Maintenance Reminders

o    Activated by Predetermined Hours

o    Clutch Engagements

o    Number of Parts Made

§  Press Lifetime Production Record

o    Hours

o    Cycle

o    Clutch Engagements

§  Minster PMConnect Production Monitoring System Interface

·         capability

§  Relay Based Primary Machine Control

§  PMC 16 Channel Die Protection Module

·         • PMC 2 Channel Load Monitor